Contents of the guide Show ▾
Quick answer Solar panels on a campervan are fixed either to a roof rack or roof bars screwed into the vehicle’s prepared mounting points, or with mounts bonded to the roof using a structural sealant-adhesive made for vehicles. The cable enters through a sealed roof entry gland, runs to an MPPT controller and on through a fuse to the battery. Run the cables and plan the cable entry before the ceiling lining goes in, and check the mounts and seals every year.
“How do you mount 2 × 200 W on a Ducato?” is a classic question in camper groups. The answer depends on the roof, the panels and whether you want to be able to remove them. How much solar power you need is worked out in the guide how much solar does a motorhome need or in the electrical calculator. This guide is about the fitting itself. Work out the cable size and fuse between the controller and the battery in the cable size calculator.
Checklist as PDF: Electrical system checklist (in Swedish). All checklists
The essentials at a glance
- Check the manufacturer’s roof load and where the vehicle has prepared mounting points.
- Roof rack, bars or bonded mounts, never just self-adhesive tape on a heavy panel.
- Air under rigid panels gives cooling and higher output.
- A sealed roof entry with a drip loop, and rust protection in the hole.
- A fuse between the controller and the battery, according to the controller’s manual.
- Measure the overall height after fitting, for garages, ferries and multi-storey car parks.
Plan the roof
Draw the roof with roof vents, roof fan, any aerial and the panels. Panels should not be shaded, because even a small shadow reduces output noticeably. How many watts you need is worked out in the guide how much solar does a motorhome need. Also check that the height with panels does not make the vehicle too tall for garages or ferries you use, and that the weight is included in the weight calculator.
Plan the roof vents at the same time; see roof vents and windows (in Swedish).
Three ways to fix the panels
| Method | Advantages | Bear in mind |
|---|---|---|
| Roof rack or cross bars in the vehicle’s mounting points | No new holes in the roof, room for other things on the rack | The rack adds weight and height. Check the permitted roof load. |
| Bonded mounts (spoiler or Z mounts) | Low height, no holes | Clean and prime according to the adhesive maker. Bond on flat surfaces, not over seams. |
| Flexible panels bonded to the roof | Low weight and height, follow curved roofs | Get hot with no air underneath and lose output. Shorter life than rigid panels. |
If you screw through the roof, only do it where you know what is underneath, rust-proof every hole and seal with a vehicle sealant. Read rust protection when drilling (in Swedish) before you drill.

The roof cable entry
- Place the entry close to the panels and where you can reach the cable route from inside, ideally above a cupboard.
- Drill the hole, deburr it and rust-proof the edge.
- Use an entry with a cable gland for the right cable diameter.
- Apply sealant according to the manufacturer and run the cable with a drip loop so that water does not follow the cable inside.
- Water-test before the ceiling lining goes in.
Warning A solar panel produces current as soon as it gets light. Cover the panel or leave the connectors unplugged while you work, and connect the controller to the battery first and the panels last, unless the manual says otherwise.
Series or parallel?
Two panels can be connected in series (higher voltage, thinner cable) or in parallel (same voltage, more current). Series works well with an MPPT controller as long as the controller’s maximum input voltage is not exceeded, even on a cold morning when the panel voltage is at its highest. Parallel copes better with shade on one panel. The controller’s manual states what it can handle. How to check the cold-weather voltage is in choosing an MPPT controller.
Running cables before the ceiling goes in
- Run the cable from the entry to the controller before the walls and ceiling are insulated and lined, ideally in conduit.
- Use solar cable that withstands UV light outdoors, and the right connectors (usually MC4).
- Place the controller close to the battery, so that the cable between them is short and heavy.
- Fuse the cable between the controller and the battery close to the battery. See cable sizes and fuses.
- Protect the cables against chafing where they pass through metal and beams.
Plan the cable routes together with the insulation (in Swedish) and the roof vents (in Swedish), so that they do not clash.
Fuses and switches
- Between the controller and the battery: a fuse close to the battery, rated for the cable.
- Between the panels and the controller: a switch lets you disconnect the panels while working. With several panels in parallel, a fuse per panel may be needed according to the panel’s data sheet.
- Connect in the right order: first the battery to the controller, then the panels, unless the manufacturer says otherwise.
More on sizing is in cable sizes and fuses for 12 V.
After fitting
- Check that the controller is set to the right battery type.
- Measure or read off the charging current on a sunny day.
- Re-tighten and check mounts and seals after the first few drives, and then every year.
- Include the weight of the panels and rack in your payload margin; see the weight calculator.
Work it out yourself: the solar calculator shows how much solar energy a panel gives per month.
Fitting a solar panel as part of a larger conversion? Read about which changes require a registration inspection (Swedish rules).
Frequently asked questions
Do I have to drill into the roof to fit solar panels?
No. Many vans have prepared mounting points for a roof rack, and there are mounts that are bonded on. The cable does need an entry, though, which usually means a hole.
Is self-adhesive tape enough?
Not for rigid panels on a vehicle driven at speed. Use mounts and adhesive or screws according to the manufacturer’s instructions.
Should a solar panel have a fuse?
The cable between the controller and the battery should always be fused close to the battery. Whether fuses are needed on the panel side depends on the number of panels and how they are connected; follow the controller and panel manuals.
How much solar do I need?
It depends on your consumption. Work it out in the solar guide or in the electrical calculator.
How do you fix a solar panel to a motorhome roof?
Most commonly with bonded corner mounts, or on a roof rack or rails. Clean, pre-treat and use a body adhesive according to the manufacturer’s instructions.
Should solar panels be connected in series or in parallel?
Series gives lower current and thinner cable; parallel copes better with shade. The voltage in series must not exceed the controller’s limit.
Is a fuse needed between the solar controller and the battery?
Yes, close to the battery and rated for the cable.
Sources
- Transportstyrelsen (the Swedish Transport Agency), Personbil (in Swedish; rules for passenger cars, including class II motorhomes)
- Data sheets for the panel, controller and adhesive (these take precedence over general advice)
- Camperliv, Campervan electrical system
- Camperliv, Electrics and off-grid: all guides
Last checked: October 2026. Always follow the manufacturer’s instructions for panels, mounts, adhesive and controller.
New checklists and guides, plus reminders before winter storage and inspection. A few emails a year, nothing more.
The content is based on my own experience and the rules that applied when the text was written. Rules can change, and I am not responsible for factual errors or rule changes that affect your build or maintenance. Read the full disclaimer.

