Contents of the guide Show ▾
Quick answer An MPPT controller is the solar charge controller most people choose for a motorhome today. Choose it by three things: the maximum voltage, meaning the panels’ open-circuit voltage (Voc) in the cold with a margin; the charging current that the panels’ power and the battery call for; and the battery type, where the controller must have the right charging profile for, say, lithium (LiFePO4). With Victron, the figures are in the name: a 100/30 can take 100 V from the panels and charges at up to 30 A.
The solar charge controller sits between the solar panels and the leisure battery and controls how the battery is charged. Here we go through the difference between PWM and MPPT, how to size the controller step by step and how to connect it. The figures come from the manufacturers’ data sheets and manuals, mainly Victron Energy.
The essentials at a glance
- MPPT converts the panels’ higher voltage into charging current and captures more energy than PWM, especially when the panel voltage is much higher than the battery’s.
- Voc in the cold must never exceed the controller’s maximum voltage. The panel voltage rises when it is cold.
- Charging current decides the size: roughly the panels’ power divided by the battery voltage.
- Panel voltage must be at least 5 V higher than the battery’s for a Victron controller to start charging.
- Connect the battery first and the panels last, according to Victron.
PWM or MPPT?
A PWM controller basically connects the panel directly to the battery and switches on and off to control charging. The panel is then forced to work at the battery’s voltage, and any voltage the panel has above that is lost. PWM therefore works best with a small panel whose voltage is close to the battery’s.
An MPPT controller (Maximum Power Point Tracking) constantly seeks out the voltage at which the panel gives the most power and converts it into the right charging voltage for the battery. The surplus voltage then becomes extra charging current instead of being lost. It also means you can connect panels in series and use thinner cable from the roof.
| PWM | MPPT | |
|---|---|---|
| Principle | Connects panel to battery, pulses | Converts panel voltage into charging current |
| Suits | A small panel with a voltage close to the battery’s | Larger systems and panels in series |
| Series connection | No benefit | Possible within the controller’s maximum voltage |
| Price | Lower | Higher |
How to size the MPPT controller
1. Maximum voltage: Voc in the cold
Find the panel’s open-circuit voltage (Voc) and the temperature coefficient for Voc in the panel’s data sheet. Voc is given at 25 °C (77 °F) and rises as it gets colder. Calculate like this:
Voc in the cold = Voc × number of panels in series × (1 + coefficient/100 × (lowest temperature − 25))
The formula uses °C. If you think in °F, convert the lowest temperature first: °C = (°F − 32) ÷ 1.8.
Worked example with made-up data-sheet values: two panels in series with a Voc of 22 V and a coefficient of −0.3 %/°C at −20 °C (−4 °F) give 44 × (1 + 0.003 × 45) ≈ 49.9 V. That fits within a 75 V controller. Victron recommends leaving a margin and calculating for the coldest temperature that can occur. Too high a voltage can destroy the controller, and that is not covered by the warranty. Victron has its own MPPT calculator on its website for exactly this check.
2. Charging current
Divide the panels’ total power by the battery voltage to get an approximate maximum charging current. 300 W on a 12 V battery gives roughly 300 / 12 = 25 A. Victron gives a nominal panel power per controller and battery voltage:
| Victron controller | Max panel voltage | Max charging current | Nominal panel power at 12 V |
|---|---|---|---|
| MPPT 75/10 | 75 V | 10 A | 145 W |
| MPPT 75/15 | 75 V | 15 A | 220 W |
| MPPT 100/20 | 100 V | 20 A | 290 W |
| MPPT 100/30 | 100 V | 30 A | 440 W |
| MPPT 100/50 | 100 V | 50 A | 700 W |
If you connect more panel power than the nominal figure, the controller limits the power. That does not damage it, as long as the voltage and the short-circuit current (Isc) stay within the data sheet’s limits. How much panel power you need is worked out in the guide how much solar does a motorhome need and with the electrical calculator.
3. Start-up voltage in the heat
The panels’ operating voltage drops when they get hot. A Victron controller only starts charging when the panel voltage is at least 5 V higher than the battery’s, and keeps going as long as it is at least 1 V higher. On a 12 V system an ordinary 12 V panel is enough, but on 24 V you may need panels in series.
Series or parallel?
- Series: the voltages add up and the current stays the same. That gives a lower current in the cable from the roof, but all panels are affected if one is shaded.
- Parallel: the currents add up and the voltage stays the same. It copes better with shade on one panel, but needs heavier cable.
Whichever you choose, Voc in the cold must stay below the controller’s maximum voltage, and the total Isc below the controller’s short-circuit current limit.
Charging profile and battery type
The controller must be set to the right battery type. Victron’s controllers have preset charging algorithms and can be adjusted in the VictronConnect app. The default values for 12 V are 14.4 V absorption and 13.8 V float, and they should be adapted to the battery maker’s recommendation, especially for lithium. Read more in lithium or AGM in a motorhome.
If you also charge from the alternator while driving, that is usually handled by a DC-DC charger (B2B). It and the solar controller can charge the same battery in parallel. See B2B chargers and smart alternators.
Installation
- Position: close to the battery but not directly above it, mounted vertically on a non-flammable surface with the cable connections facing down, according to Victron.
- Connect the battery first and wait about 10 seconds so that the controller detects the system voltage. Connect any loads, and the panels last.
- Fuse between the controller and the battery, close to the battery.
- Switch between the panel and the controller, so that the panels can be disconnected while you work.
- Cable size by current and length; see cable sizes and fuses for 12 V.
- Tighten the connections to the torque given in the manual.
Victron also writes that panel optimisers should not be used with its controllers. The physical fitting on the roof is covered in fitting a solar panel on a motorhome, and the whole living-area electrical system in the guide to the campervan electrical system.
Warning Solar panels produce voltage as soon as light hits them, and a battery can deliver a very high short-circuit current. Check the polarity before connecting, fuse the cables close to the battery and cover the panels or break the circuit when you work on the system.
Is the electrical system part of a conversion? The rules guide for motorhomes and campervans covers inspection and electrics (Swedish rules).
Frequently asked questions
What is the difference between PWM and MPPT?
PWM connects the panel directly to the battery, and any voltage above the battery’s is lost. MPPT converts the higher panel voltage into extra charging current and therefore captures more energy.
What size MPPT controller do I need?
Divide the panels’ power by the battery voltage to get the charging current, for example 300 W / 12 V ≈ 25 A. Then check that the panels’ cold-weather Voc stays below the controller’s maximum voltage.
What does 100/30 mean on a Victron controller?
That it can take at most 100 V from the panels and charges the battery at up to 30 A.
Can I connect more watts than the controller is rated for?
According to Victron, the controller limits the power if more panel power is connected, but the panel voltage and short-circuit current must always stay within the data sheet’s limits.
Should I connect the solar panels in series?
With MPPT, series gives a lower current and thinner cable, but makes the system more sensitive to shade. Cold-weather Voc must stay below the controller’s maximum voltage.
Is a fuse needed between the solar panel and the controller?
A fuse is always needed between the controller and the battery. A switch is recommended between the panel and the controller. Whether the panel side also needs fuses depends on the number of parallel strings and the panels’ data sheet.
Sources and further reading
- Victron Energy, SmartSolar MPPT 100/30 and 100/50 manual (PDF)
- Victron Energy, MPPT 100/30 and 100/50 data sheet (PDF)
- Victron Energy, Technical specifications, MPPT 75/10 to 100/20
- Victron Energy, Installation and connection order, SmartSolar MPPT
- Camperliv, How much solar does a motorhome need?
Last checked: October 2026. Always follow the manufacturer’s manual for your controller and panels.
New checklists and guides, plus reminders before winter storage and inspection. A few emails a year, nothing more.
The content is based on my own experience and the rules that applied when the text was written. Rules can change, and I am not responsible for factual errors or rule changes that affect your build or maintenance. Read the full disclaimer.

